Horner-apg QX351 OCS HEQX351C103 Manuel d'utilisateur télécharger pdf (Page 5)

MAN0893-02-EN Specifications / Installation

________________________________________________________________________________________________________________________________________

Feb 2, 2010 Page 5 of 5 #1039

5. Safety

When found on the product, the following symbols specify:

Warning: Electrical

Shock Hazard.

Warning: Consult

user documentation.

This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D

or Non-hazardous locations only

WARNING – EXPLOSION HAZARD – Do not disconnect equipment unless

power has been switched off or the area is known to be non-hazardous.

AVERTISSEMENT - RISQUE D'EXPLOSION - AVANT DE DECONNECTOR

L'EQUIPMENT, COUPER LE COURANT OU S'ASSURER QUE

L'EMPLACEMENT EST DESIGNE NON DANGEREUX.

WARNING: To avoid the risk of electric shock or burns, always connect the

safety (or earth) ground before making any other connections.

WARNING: To reduce the risk of fire, electrical shock, or physical injury it is

strongly recommended to fuse the voltage measurement inputs. Be sure to

locate fuses as close to the source as possible.

WARNING: Replace fuse with the same type and rating to provide protection

against risk of fire and shock hazards.

WARNING: In the event of repeated failure, do not replace the fuse again as a

repeated failure indicates a defective condition that will not clear by replacing

the fuse.

WARNING – EXPLOSION HAZARD – Substitution of components may impair

suitability for Class I, Division 2

AVERTISSEMENT - RISQUE D'EXPLOSION - LA SUBSTITUTION DE

COMPOSANTS PEUT RENDRE CE MATERIAL INACCEPTABLE POUR LES

EMPLACEMENTS DE CLASSE 1, DIVISION 2

WARNING - The USB parts are for operational maintenance only. Do not leave

permanently connected unless area is known to be non-hazardous.

WARNING – EXPLOSION HAZARD - BATTERIES MUST ONLY BE

CHANGED IN AN AREA KNOWN TO BE NON-HAZARDOUS

AVERTISSEMENT - RISQUE D'EXPLOSION - AFIN D'EVITER TOUT

RISQUE D'EXPLOSION, S'ASSURER QUE L'EMPLACEMENT EST DESIGNE

NON DANGEREUX AVANT DE CHANGER LA BATTERIE

WARNING - Battery May Explode If Mistreated. Do Not Recharge, Disassemble

or Dispose Of In Fire

WARNING: Only qualified electrical personnel familiar with the construction

and operation of this equipment and the hazards involved should install, adjust,

operate, or service this equipment. Read and understand this manual and other

applicable manuals in their entirety before proceeding. Failure to observe this

precaution could result in severe bodily injury or loss of life.

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference

that may cause undesired operation.

Radiated Emission Compliance: For compliance requirement, a ferrite

(Horner P/N FBD006 supplied with the unit) needs to be placed on the AC/DC

line with one loop.

 All applicable codes and standards need to be followed in the installation of this

product.

 Adhere to the following safety precautions whenever any type of connection is

made to the module:

 Connect the safety (earth) ground on the power connector first before making

any other connections.

 When connecting to electric circuits or pulse-initiating equipment, open their

related breakers.

 Do not make connections to live power lines.

 Make connections to the module first; then connect to the circuit to be

monitored.

 Route power wires in a safe manner in accordance with good practice and local

codes.

 Wear proper personal protective equipment including safety glasses and

insulated gloves when making connections to power circuits.

 Ensure hands, shoes, and floors are dry before making any connection to a

power line.

 Make sure the unit is turned OFF before making connection to terminals.

 Make sure all circuits are de-energized before making connections.

 Before each use, inspect all cables for breaks or cracks in the insulation.

Replace immediately if defective.

• Use Copper Conductors in Field Wiring Only, 60/75° C

Technical Support

For assistance and Manual updates, contact Technical Support at the following

locations:

North America:

Tel: 317-916–4274

Fax: 317-639-4279

Web: www.heapg.com

Email: techsppt@heapg.com

Europe:

Tel: +353–21–4321–266

Fax: +353-21-4321-826

Web: www.horner-apg.com

Email: techsupport@horner-apg.com

No part of this publication may be reproduced without the prior agreement and

written permission of Horner APG, Inc. Information in this document is subject to

change without notice.

1 2 3 4 5

Commentaires sur ces manuels

Pas de commentaire

Horner-apg QX351 OCS HEQX351C103 Manuel d'utilisateur Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Capteurs Horner-apg QX351 OCS HEQX351C103