Horner-apg QX501 OCS HE-QX501 Manuel d'utilisateur télécharger pdf (Page 3)

MAN0967-01-EN Specifications / Installation

__________________________________________________________________________________________________________________________________________________________________________

8/24/2012 #1037

4.4 Ethernet Port

4.5 Power Port and Wiring

4.6 Memory Card and USB Support

Micro SD Memory Slot:

Uses Removable Memory for data logging, screen captures, program

loading and recipes. Supports cards up to 2GB in capacity.

Horner Part No.: HE-MC1 (2GB MicroSD Card)

USBA: For flash drive connectivity for transferring data to and from the

microSD Card using Removable Memory Functions (Copy, Erase, etc.).

Uses FLASH drives up to 2GB capacity.

USBB: For data communications and programming of OCS. Uses mini-B

Type Connector.

4.7 SmartStack I/O (local & connected via FOX)

The QX501 supports local expansion I/O utilizing SmartStack I/O. Up to 4

Plastic SmartStack I/O modules may be stacked directly on the back of the

QX unit. For applications with harsh shock and vibration conditions, it may

be advisable to limit the number of local SmartStack I/O modules to two.

The QX also supports Remote Expansion of the SmartStack I/O bus via

Fiber Optic Expansion (FOX) ports. FOX utilizes plastic fiber optic cables

(available from Horner APG) to remotely locate bases of additional

SmartStack I/O up to 10m away from the QX unit.

6 Technical Support

For assistance and manual updates, contact Technical Support at the

following locations:

North America:

Tel: 317 916-4274

Fax: 317 639-4279

Web: http://www.heapg.com

Email: techsppt@heapg.com

Europe:

Tel: +353-21-4321266

Fax: +353-21-4321826

Web: http://www.horner-apg.com

Email: tech.support@horner-apg.com

5 Safety

No part of this publication may be reproduced without the prior agreement and written permission of

Horner APG, Inc. Information in this document is subject to change without notice.

Speeds

10 BaseT Ethernet (10-Mbps)

100 BaseTx Fast Ethernet (100-Mbps)

Modes

Half or Full Duplex

Auto-Negotiation

Both 10/100-Mbps and Half/Full Duplex

Connector Type

Shielded RJ-45

Cable Type

(Recommended)

CAT5 (or better) UTP

Port

Auto MDI/MDI-X

Primary Power Port Pins

Signal

Description

Ground

Frame Ground

V-

Input Power Supply Ground

V+

Input Power Supply Voltage

Torque rating 4.5 – 7 Lb-In

(0.50 – 0.78 N-m)

This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D or Non-hazardous

locations only.

WARNING – EXPLOSION HAZARD – Do not disconnect equipment unless power has been switched

off or the area is known to be non-hazardous.

AVERTISSEMENT - RISQUE D'EXPLOSION - AVANT DE DECONNECTOR L'EQUIPMENT,

COUPER LE COURANT OU S'ASSURER QUE L'EMPLACEMENT EST DESIGNE NON

DANGEREUX.

WARNING: To avoid the risk of electric shock or burns, always connect the safety (or earth) ground

before making any other connections.

WARNING: To reduce the risk of fire, electrical shock, or physical injury it is strongly recommended to

fuse the voltage measurement inputs. Be sure to locate fuses as close to the source as possible.

WARNING: Replace fuse with the same type and rating to provide protection against risk of fire and

shock hazards.

WARNING: In the event of repeated failure, do not replace the fuse again as a repeated failure

indicates a defective condition that will not clear by replacing the fuse.

WARNING – EXPLOSION HAZARD – Substitution of components may impair suitability for Class I,

Division 2

AVERTISSEMENT - RISQUE D'EXPLOSION - LA SUBSTITUTION DE COMPOSANTS PEUT

RENDRE CE MATERIAL INACCEPTABLE POUR LES EMPLACEMENTS DE CLASSE 1, DIVISION 2.

WARNING - The USB parts are for operational maintenance only. Do not leave permanently connected

unless area is known to be non-hazardous.

WARNING – EXPLOSION HAZARD - BATTERIES MUST ONLY BE CHANGED IN AN AREA

KNOWN TO BE NON-HAZARDOUS.

AVERTISSEMENT - RISQUE D'EXPLOSION - AFIN D'EVITER TOUT RISQUE D'EXPLOSION,

S'ASSURER QUE L'EMPLACEMENT EST DESIGNE NON DANGEREUX AVANT DE CHANGER LA

BATTERIE.

WARNING - Battery May Explode If Mistreated. Do Not Recharge, Disassemble or Dispose Of In Fire

WARNING: Only qualified electrical personnel familiar with the construction and operation of this

equipment and the hazards involved should install, adjust, operate, or service this equipment. Read

and understand this manual and other applicable manuals in their entirety before proceeding. Failure to

observe this precaution could result in severe bodily injury or loss of life.

" All applicable codes and standards need to be followed in the installation of this product.

" Adhere to the following safety precautions whenever any type of connection is made to the module:

# Connect the safety (earth) ground on the power connector first before making any other connections.

# When connecting to electric circuits or pulse-initiating equipment, open their related breakers.

# Do not make connections to live power lines.

# Make connections to the module first; then connect to the circuit to be monitored.

# Route power wires in a safe manner in accordance with good practice and local codes.

# Wear proper personal protective equipment including safety glasses and insulated gloves when

making connections to power circuits.

# Ensure hands, shoes, and floor are dry before making any connection to a power line.

# Make sure the unit is turned OFF before making connection to terminals.

# Make sure all circuits are de-energized before making connections.

# Before each use, inspect all cables for breaks or cracks in the insulation. Replace immediately

if defective.

Warning: Consult

user documentation.

Warning: Electrical

Shock Hazard.

When found on the product, the following symbols specify:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause

undesired operation.

Radiated Emission Compliance: For compliance requirement, a ferrite (Horner P/N FBD006 supplied

with the unit) needs to be placed on the AC/DC line with one loop.

1 2 3

Mounting Clip 1
Locations 1

Commentaires sur ces manuels

Pas de commentaire

Horner-apg QX501 OCS HE-QX501 Manuel d'utilisateur Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Capteurs Horner-apg QX501 OCS HE-QX501